Products

Manhattan Computer Products 152051 SuperSpeed+ USB-C 3.1 to DVI Converter The Manhattan SuperSpeed+ USB-C to DVI Converter establishes a fast, simple and convenient link between a newer USB type-C equipped media source (e.g., computer, tablet, etc.) and an existing DVI display (e.g., monitor, projector, etc.). The Manhattan SuperSpeed+ USB-C to DVI Converter is easy and quick to install — no complicated configuration or setup required. Its all-in-one design achieves a compact, integrated solution that eliminates unnecessary cables, tangles and clutter to keep installations and work spaces neat and orderly. Extend the service life of your equipment, and fully realize the investment and value of your DVI displays, projectors and peripherals with the Manhattan SuperSpeed+ USB-C to DVI Converter. Features: Converts a USB signal to a DVI video display Delivers High-Definition (HD) media to a DVI monitor, projector or other display device Supports video resolutions up to 3840x2160p@30Hz Compliant with DisplayPort 1.2 Alternate Mode (DP Alt Mode) Plug and Play; requires no external power supply Compatible with all USB type-C supported desktops, notebooks and tablets including Apple MacBook®, Chromebook Pixel™ and more Compatible with DVI-I and DVI-D interfaces Fully shielded to reduce EMI and other interference sources Molded PVC boot and strain relief Lifetime warranty Specifications: Standards and Certifications USB 3.1 DVI CE FCC RoHS2 WEEE Connections USB type-C, 24-pin, male DVI-I, 29-pin, female Shielded Video Resolutions 640x480, 800x600, 1024x768, 1920x1200, 3840x2160p@30Hz Physical 32-AWG cable gauge Mylar and aluminum shielding Thermal plastic casing Length: 8 cm (3 in.) Weight: 31 g (1.1 oz.) Shielded Housing: ABS plastic Operating Environment Operation Temperature: 0 – 50°C (32 – 122°F) Storage Temperature: -20 – 85°C (-4 – 185°F) Humidity (noncondensing): 0 – 96% System Requirements Windows XP/Vista/7/8.1/10 or Linux or Mac 9.x/10.x or above Package Contents SuperSpeed+ USB-C to DVI Converter

Read more less

MG Chemicals MG442 25 Ft. SUPERWICK - #2 Yellow Non-Static 0.05" Diameter The MG Chemicals MG442 SUPERWICK is a high-performance desoldering braid designed for efficient and precise removal of solder. This 25-foot, #2 yellow braid features a 0.05-inch diameter and is non-static, making it ideal for use in sensitive electronic environments. The SUPERWICK braid is perfect for rework and repair tasks, providing reliable and clean desoldering with minimal residue. Features High Efficiency: Excellent wicking action for quick and effective solder removal. Non-Static: Safe for use with sensitive electronic components. Precise Diameter: 0.05-inch diameter suitable for a wide range of applications. Color-Coded: #2 yellow braid for easy identification. Length: 25 feet, providing ample material for multiple uses. Specifications Length: 25 feet Color: Yellow (#2) Diameter: 0.05 inches (1.27 mm) Material: Copper braid Flux: Rosin Non-Static: Yes Example Use Scenario The MG Chemicals MG424 SUPERWICK is ideal for repairing a PCB where excess solder needs to be removed from solder joints. For instance, when replacing a damaged component, the SUPERWICK effectively removes the old solder, allowing for a clean and precise installation of the new component. This braid is particularly useful in applications where sensitive electronic components are involved, ensuring that no static electricity is introduced during the desoldering process. How to Use MG Chemicals MG442 SUPERWICK Preparation: Ensure the work area is clean and well-lit. Secure the PCB or component to prevent movement during the desoldering process. Application: Select the appropriate size of SUPERWICK for the job. Place the end of the braid over the solder joint to be desoldered. Heating: Heat your soldering iron to the appropriate temperature. Place the soldering iron tip on top of the braid, directly over the solder joint. Allow the heat to transfer through the braid to the solder, which will then be wicked up into the braid. Removal: Once the solder has been absorbed, remove the braid and soldering iron from the joint. Cut off and discard the used section of the braid. Cleaning: Inspect the area to ensure all solder has been removed. If necessary, repeat the process with a fresh section of braid until the joint is clean. Additional Information Tri-Tek Electronics is an authorized distributor of MG Chemicals products, ensuring you receive full manufacturer warranty coverage and the best pricing and factory support.

Read more less

MG Chemicals MG424 5 Ft. SUPERWICK - #2 Yellow Non-Static 0.05" Diameter The MG Chemicals MG424 SUPERWICK is a high-performance desoldering braid designed for efficient and precise removal of solder. This 5-foot, #2 yellow braid features a 0.05-inch diameter and is non-static, making it ideal for use in sensitive electronic environments. The SUPERWICK braid is perfect for rework and repair tasks, providing reliable and clean desoldering with minimal residue. Features High Efficiency: Excellent wicking action for quick and effective solder removal. Non-Static: Safe for use with sensitive electronic components. Precise Diameter: 0.05-inch diameter suitable for a wide range of applications. Color-Coded: #2 yellow braid for easy identification. Length: 5 feet, providing ample material for multiple uses. Specifications Length: 5 feet Color: Yellow (#2) Diameter: 0.05 inches (1.27 mm) Material: Copper braid Flux: Rosin Non-Static: Yes Example Use Scenario The MG Chemicals MG424 SUPERWICK is ideal for repairing a PCB where excess solder needs to be removed from solder joints. For instance, when replacing a damaged component, the SUPERWICK effectively removes the old solder, allowing for a clean and precise installation of the new component. This braid is particularly useful in applications where sensitive electronic components are involved, ensuring that no static electricity is introduced during the desoldering process. How to Use MG Chemicals MG424 SUPERWICK Preparation: Ensure the work area is clean and well-lit. Secure the PCB or component to prevent movement during the desoldering process. Application: Select the appropriate size of SUPERWICK for the job. Place the end of the braid over the solder joint to be desoldered. Heating: Heat your soldering iron to the appropriate temperature. Place the soldering iron tip on top of the braid, directly over the solder joint. Allow the heat to transfer through the braid to the solder, which will then be wicked up into the braid. Removal: Once the solder has been absorbed, remove the braid and soldering iron from the joint. Cut off and discard the used section of the braid. Cleaning: Inspect the area to ensure all solder has been removed. If necessary, repeat the process with a fresh section of braid until the joint is clean. Additional Information Tri-Tek Electronics is an authorized distributor of MG Chemicals products, ensuring you receive full manufacturer warranty coverage and the best pricing and factory support.

Read more less

MG Chemicals 444 SUPERWICK #4 Blue Non-Static Solder Wick 0.10" Diameter 25ft. The MG Chemicals 444 SUPERWICK #4 Blue Non-Static Solder Wick is designed for efficient and precise removal of solder in electronic repair and rework tasks. This 25-foot desoldering braid features a 0.10-inch diameter and is non-static, making it safe and ideal for use with sensitive electronic components. Features High Efficiency: Excellent wicking action for quick and effective solder removal. Non-Static: Safe for use with sensitive electronic components. Precise Diameter: 0.10-inch diameter suitable for a wide range of applications. Color-Coded: #4 blue braid for easy identification. Length: 25 feet, providing ample material for extensive use. Specifications Length: 25 feet Color: Blue (#4) Diameter: 0.10 inches (2.54 mm) Material: Copper braid Flux: Rosin Non-Static: Yes Example Use Scenario The MG Chemicals 444 SUPERWICK is ideal for desoldering components from PCBs, such as removing a faulty multi-pin IC from a motherboard. By using the SUPERWICK, technicians can efficiently wick away the solder, allowing for clean and precise component removal. This braid is particularly useful in applications involving sensitive electronic components, ensuring no static electricity is introduced during the desoldering process. How to Use MG Chemicals 444 SUPERWICK Preparation: Ensure the work area is clean and well-lit. Secure the PCB or component to prevent movement during the desoldering process. Application: Select the appropriate size of SUPERWICK for the job. Place the end of the braid over the solder joint to be desoldered. Heating: Heat your soldering iron to the appropriate temperature. Place the soldering iron tip on top of the braid, directly over the solder joint. Allow the heat to transfer through the braid to the solder, which will then be wicked up into the braid. Removal: Once the solder has been absorbed, remove the braid and soldering iron from the joint. Cut off and discard the used section of the braid. Cleaning: Inspect the area to ensure all solder has been removed. If necessary, repeat the process with a fresh section of braid until the joint is clean. Additional Information Tri-Tek Electronics is an authorized distributor of MG Chemicals products, ensuring you receive full manufacturer warranty coverage and the best pricing and factory support.

Read more less

MG Chemicals 427 SUPERWICK #5 Brown Non-Static Solder Wick 0.125" Diameter 5ft. The MG Chemicals 427 SUPERWICK #5 Brown Non-Static Solder Wick is designed for efficient and precise removal of solder in electronic repair and rework tasks. This 5-foot desoldering braid features a 0.125-inch diameter and is non-static, making it safe and ideal for use with sensitive electronic components. Features High Efficiency: Excellent wicking action for quick and effective solder removal. Non-Static: Safe for use with sensitive electronic components. Precise Diameter: 0.125-inch diameter suitable for a wide range of applications. Color-Coded: #5 brown braid for easy identification. Length: 5 feet, providing ample material for multiple uses. Specifications Length: 5 feet Color: Brown (#5) Diameter: 0.125 inches (3.2 mm) Material: Copper braid Flux: Rosin Non-Static: Yes Example Use Scenario The MG Chemicals 427 SUPERWICK is ideal for desoldering larger components from PCBs. For instance, when replacing a large through-hole component such as a power transistor, the SUPERWICK effectively removes the excess solder, allowing for clean and precise installation of the new component. This braid is particularly useful in applications involving sensitive electronic components, ensuring that no static electricity is introduced during the desoldering process. How to Use MG Chemicals 427 SUPERWICK Preparation: Ensure the work area is clean and well-lit. Secure the PCB or component to prevent movement during the desoldering process. Application: Select the appropriate size of SUPERWICK for the job. Place the end of the braid over the solder joint to be desoldered. Heating: Heat your soldering iron to the appropriate temperature. Place the soldering iron tip on top of the braid, directly over the solder joint. Allow the heat to transfer through the braid to the solder, which will then be wicked up into the braid. Removal: Once the solder has been absorbed, remove the braid and soldering iron from the joint. Cut off and discard the used section of the braid. Cleaning: Inspect the area to ensure all solder has been removed. If necessary, repeat the process with a fresh section of braid until the joint is clean. Additional Information Tri-Tek Electronics is an authorized distributor of MG Chemicals products, ensuring you receive full manufacturer warranty coverage and the best pricing and factory support.

Read more less

Introducing the Hellermann Tyton SMBSIX-I Surface Mount Box, an essential solution for your networking needs. 🔹 Dimensions: 6.69" x 1.36" x 4.33" 🔹 Material: PVC 🔹 Colour: Ivory 🔹 6-port design for versatile connectivity 🔹 Easy-to-use cover that snaps on and off for quick adjustments 🔹 Knockouts on 3 sides for seamless integration with HellermannTyton’s TSR single channel raceway Designed for electronics technicians, IT professionals, and low voltage installers, this Surface Mount Box offers unparalleled convenience and performance. The Ivory finish adds a touch of elegance to any installation, while the durable PVC material ensures long-lasting reliability. Tri-Tek Electronics proudly serves as an authorised distributor of Hellermann Tyton products, guaranteeing authenticity and quality assurance. Don't miss out on this closeout special - order now to secure this premium product at a limited-time price, subject to availability!

Read more less

PI Mfg TTA‑1178 Surface Mount Mini IR Receiver — Closeout Special Overview The PI Manufacturing TTA‑1178 Surface Mount Mini IR Receiver (Dual Band) is a compact, low-profile infrared sensor module designed to receive IR commands from remote controls over both standard and expanded IR bands. As a closeout item, it is offered in limited quantities, while stock lasts. As an authorized distributor, Tri‑Tek Electronics provides full manufacturer warranty coverage and local support for installers, AV integrators, and system designers in the Phoenix / Mesa, AZ region. Key Features Dual‑band infrared reception (supports broad IR remote frequencies) IR pickup range up to ~ 40 feet Blue LED indicator to confirm IR reception 3-meter integral cable (prewired) 3.5 mm stereo mini‑plug connector Tip = Signal Ring = +V Sleeve = Ground Surface‑mountable housing, unobtrusive design Compact footprint ideal for tight installations Typical Use / Installation Example This mini IR receiver is ideal for home theater, custom AV racks, or cabinetry where you wish to place an IR “eye” behind a small window (e.g. plastic or acrylic) or exposed discreetly. You mount the unit in a flush or surface-mount position and route the cable back to your IR control system or IR repeater block. The dual-band design ensures compatibility with a wider variety of remote control frequencies, minimizing “dead zone” issues. For example, in a media cabinet with smoked glass doors, you might install the TTA‑1178 directly behind a small IR-transparent decal or window. The 3 m cable then carries the IR signal back to your IR processor or system controller. Specifications Parameter Specification IR Frequency / Band Dual band (wide remote compatibility) Range ~ 40 ft Indicator Blue LED (IR reception confirmation) Cable Length 3 meters Connector 3.5 mm stereo mini‑plug Pinout Tip = Signal, Ring = +V, Sleeve = Ground Mounting Surface mount housing (low profile) Warranty Full manufacturer warranty via Tri‑Tek Electronics Special Note Closeout item — limited inventory Important Notes & Recommendations Because this is a closeout product, once current inventory is depleted, it will not be restocked. Use care when routing the IR cable: avoid sharp bends and maintain good grounding to reduce noise or interference. The LED confirmation helps with alignment and setup: place the receiver eye where the LED is visible during commissioning. If mounting behind a cover or window, ensure the covering material is IR‑transparent (e.g. thin acrylic, IR-permeable plastic) to avoid signal attenuation. In long cable runs, verify voltage at the receiver end and avoid excessive voltage drop. Why Buy Through Tri‑Tek Electronics? Authorized distributor status ensures full factory warranty, product authenticity, and support. Local AZ presence in Mesa / Phoenix ensures faster delivery, easier returns, and local technical assistance. Closeout pricing advantage—you benefit from reduced cost while quality remains factory-grade. Would you like me to prepare a wiring diagram, high‑res render of the unit for your web page, or a printable installation guide?

Read more less

Steren 905-308, Surge Supressor 6-Outlet Wall Mount   Steren 905-308 Surge Supressor 6-Outlet Wall Mount Tap Phone Modem Fax Surge Protector 420 Joules 3-Line Protection LED Indicator Light 120 VAC UL Listed Plug-In wall mounted surge protector. Specifications: 3-wire NEMA 5-15 grounded outlets High impact ABS plastic housing 120 VAC, 15 A, 1875 W EMI-RFI Noise Filtration 420 Joules Response Time < 1 ns UL Listed  

Read more less

Switch Craft 3C XLR Inline Jack The Switchcraft AAA3FZ is a premium 3-pin XLR female connector, part of Switchcraft's renowned AAA Series. Known for its robust design and reliable performance, this connector is ideal for professional audio applications, including live sound, recording studios, and broadcast environments. The AAA3FZ features Switchcraft’s unique low-profile design and the company's easy-to-assemble "Z" series components, which ensure secure and durable connections. Product Features: Connector Type: 3-pin XLR Female Series: AAA Series (also known as the "Z" series) Design: Low-profile design with a compact, lightweight construction for easy integration into tight spaces Contacts: Precision-machined, silver-plated contacts for optimal signal integrity and minimal signal loss Housing: Rugged metal shell designed to withstand heavy use and resist wear and tear Assembly: Simple, no-solder design for quick and easy cable assembly Application: Ideal for use in professional audio environments, such as live sound, recording studios, and broadcast setups Example Installation Scenario The Switchcraft AAA3FZ connector is perfect for assembling custom microphone cables in a recording studio. Its easy-to-assemble design allows for quick setup, while the durable construction ensures that the connector will hold up under frequent use. This connector is especially useful in environments where reliable, high-quality audio connections are critical. Tri-Tek Electronics: Your Authorized Distributor Tri-Tek Electronics is an authorized distributor of Switchcraft products, including the AAA3FZ XLR Female Connector. When you purchase from us, you benefit from full manufacturer warranty coverage, competitive pricing, and expert factory support. Visit our retail location in Mesa, AZ, to purchase this connector and receive personalized advice from our knowledgeable staff.

Read more less

Switchcraft AAA3FZ, 3-Pin XLR Female Mic Connector Cable Mount Product Overview The Switchcraft AAA3FZ is a premium 3-Pin XLR Female Mic Connector, designed for professional audio applications requiring high-quality signal transmission and reliable performance. This cable mount connector is part of Switchcraft's renowned AAA Series, known for its rugged durability and superior engineering. It is an essential component for building or repairing XLR cables used in audio systems, microphones, and other equipment. Switchcraft, a leading manufacturer of connectors and audio components, ensures that the AAA3FZ provides excellent connectivity with minimal signal loss, making it a top choice for audio professionals, installers, and technicians. Features Connector Type: 3-Pin XLR Female Mounting Style: Cable Mount Durable Construction: Metal shell provides long-lasting durability Easy Assembly: Solder-style terminals for secure wire connections Gold-Plated Contacts: Ensures excellent conductivity and resistance to corrosion Compact Design: Ideal for tight spaces and professional setups Color: Black (with optional color-coded boots for easy identification) Specifications Connector Type: XLR Female Number of Pins: 3 Termination: Solder terminals Shell Material: Metal with nickel plating Contact Material: Gold-plated for optimal conductivity Current Rating: 15A Operating Temperature: -55°C to +85°C Dimensions: Standard XLR size compatible with most XLR plugs Installation Scenario The Switchcraft AAA3FZ is ideal for assembling custom microphone cables, especially in live sound environments where reliability is paramount. For example, this connector can be used in a home studio to create custom-length XLR cables that connect microphones to audio interfaces or mixers, ensuring clean, high-quality audio capture with minimal interference. Its durable design makes it suitable for on-the-road use in demanding environments such as touring or event production. Why Choose Switchcraft AAA3FZ? Professional-Grade Quality: Trusted by audio professionals worldwide for its reliability and performance. Easy to Use: Designed for straightforward installation with solder-style terminals. Long-Lasting Durability: Built to withstand rigorous use in professional audio environments. Versatility: Suitable for a wide range of applications, from home studios to large-scale live events. As an authorized distributor of Switchcraft products, Tri-Tek Electronics ensures that you receive the full manufacturer's warranty and the best support and pricing available. Visit our retail location in Mesa, AZ, or shop online for expert assistance with your audio connectivity needs. The Switchcraft AAA3FZ is a premium 3-Pin XLR Female Mic Connector, designed for professional audio applications requiring high-quality signal transmission and reliable performance. This cable mount connector is part of Switchcraft's renowned AAA Series, known for its rugged durability and superior engineering. It is an essential component for building or repairing XLR cables used in audio systems, microphones, and other equipment. Switchcraft, a leading manufacturer of connectors and audio components, ensures that the AAA3FZ provides excellent connectivity with minimal signal loss, making it a top choice for audio professionals, installers, and technicians. Features Connector Type: 3-Pin XLR Female Mounting Style: Cable Mount Durable Construction: Metal shell provides long-lasting durability Easy Assembly: Solder-style terminals for secure wire connections Gold-Plated Contacts: Ensures excellent conductivity and resistance to corrosion Compact Design: Ideal for tight spaces and professional setups Color: Black (with optional color-coded boots for easy identification) Specifications Connector Type: XLR Female Number of Pins: 3 Termination: Solder terminals Shell Material: Metal with nickel plating Contact Material: Gold-plated for optimal conductivity Current Rating: 15A Operating Temperature: -55°C to +85°C Dimensions: Standard XLR size compatible with most XLR plugs Installation Scenario The Switchcraft AAA3FZ is ideal for assembling custom microphone cables, especially in live sound environments where reliability is paramount. For example, this connector can be used in a home studio to create custom-length XLR cables that connect microphones to audio interfaces or mixers, ensuring clean, high-quality audio capture with minimal interference. Its durable design makes it suitable for on-the-road use in demanding environments such as touring or event production. Why Choose Switchcraft AAA3FZ? Professional-Grade Quality: Trusted by audio professionals worldwide for its reliability and performance. Easy to Use: Designed for straightforward installation with solder-style terminals. Long-Lasting Durability: Built to withstand rigorous use in professional audio environments. Versatility: Suitable for a wide range of applications, from home studios to large-scale live events. As an authorized distributor of Switchcraft products, Tri-Tek Electronics ensures that you receive the full manufacturer's warranty and the best support and pricing available. Visit our retail location in Mesa, AZ, or shop online for expert assistance with your audio connectivity needs.

Read more less

PHC Enterprises SW-122T3 Switching 12VDC 2.2A w/Screw Terminals The PHC Enterprises SW-122T3 is a robust and reliable 12V DC switching power supply designed for a wide range of low-voltage applications. Featuring screw terminals for easy and secure connections, this power supply ensures efficient and stable performance, making it an ideal choice for both professional installers and DIY enthusiasts. The SW-122T3 is engineered to deliver 2.2A of continuous current, providing ample power for various electronic devices and systems. As an authorized distributor, Tri-Tek Electronics guarantees that all PHC Enterprises products come with full manufacturer warranty coverage, ensuring the best pricing and factory support. Key Features Input Voltage: 100-240V AC, 50/60Hz Output Voltage: 12V DC Output Current: 2.2A continuous Connections: Screw terminals for secure and easy installation Efficiency: High efficiency with minimal heat generation Protections: Over-voltage, over-current, and short-circuit protections Certifications: UL, CE, RoHS compliant Specifications Feature Specification Input Voltage 100-240V AC, 50/60Hz Output Voltage 12V DC Output Current 2.2A Power Efficiency >85% Dimensions 80mm x 50mm x 35mm Weight 150g Operating Temperature -20°C to +50°C Storage Temperature -40°C to +85°C Humidity 20% to 90% non-condensing Mounting Type Surface mountable Protection Class Class II Applications The PHC Enterprises SW-122T3 is perfect for a variety of applications including: Security Systems: Powering cameras, sensors, and control panels. LED Lighting: Suitable for low-voltage LED strips and modules. Home Automation: Ideal for smart home devices and controllers. Industrial Equipment: Reliable power source for industrial control systems. Electronics Projects: Great for hobbyists and prototype development. Installation Example For a typical installation, the SW-122T3 can be mounted on a flat surface inside a protective enclosure. The screw terminals make it straightforward to connect the power supply to your devices. For instance, in a security system setup, the SW-122T3 can provide a steady 12V DC to multiple cameras and sensors, ensuring uninterrupted surveillance. Why Choose Tri-Tek Electronics? As a trusted partner of PHC Enterprises, Tri-Tek Electronics offers authorized distribution of the SW-122T3 power supply. This ensures that you receive genuine products with complete manufacturer warranty and support. Our commitment to quality and customer satisfaction means you can count on us for the best service and value.

Read more less

Syston Cable 1258-PB-BK-1000 SySPEED Premium Cat 6 Ethernet Cable – 1000 ft. Black The Syston Cable 1258-PB-BK-1000 is a premium-grade Category 6 Ethernet cable designed to meet the demands of high-speed data transmission and network infrastructure. This 1000-foot spool of black cable features 23 AWG solid bare copper conductors, ensuring excellent conductivity and reduced signal loss across long runs. Ideal for structured cabling installations in commercial buildings, residential networks, and industrial settings, this cable supports bandwidths up to 600 MHz and is fully compatible with 10/100/1000BASE-T networks. Its CMR (riser-rated) jacket provides a flame-retardant and sunlight-resistant solution that complies with building codes for vertical installations between floors. Product Features: Cable Type: Category 6 (Cat 6) Conductor Material: Solid bare copper, 23 AWG Cable Construction: 4 Unshielded Twisted Pairs (UTP) Jacket Rating: CMR (Riser), FT4, sunlight resistant Bandwidth Performance: Up to 600 MHz Color: Black Cable Length: 1000 feet (304.8 meters) Applications: Ethernet (10/100/1000BASE-T), PoE/PoE+, VoIP, IP surveillance, and other high-speed data networks Example Installation Use: This cable is especially well-suited for professional installers working on network backbones in multi-story buildings. For instance, when connecting floor-to-floor switches in a business environment, the Syston Cat 6 cable ensures clean data signals for IP cameras, workstations, and wireless access points—making it an excellent solution for reliable, high-speed data transmission over riser spaces. Tri-Tek Electronics – Your Authorized Syston Cable Distributor Tri-Tek Electronics is proud to be an authorized distributor of Syston Cable products, offering full manufacturer warranty coverage and direct access to technical support. Visit our retail store in Mesa, Arizona—serving the Phoenix metro area including Chandler, Gilbert, Scottsdale, Tempe, and Glendale—for all your professional networking and structured cabling needs.

Read more less