Products
Pan Pacific ADAPTOR, N MALE TO UHF FEMALE
$8.56 $7.69
Pan Pacific ADAPTOR, SMA FEMALE TO BNC MALE
$6.96 $6.29
Pan Pacific ADAPTOR, SMA FEMALE TO TNC MALE
$6.50 $5.89
Pan Pacific ADAPTOR, SMA FEMALE TO UHF FEMALE
$7.16 $6.49
Pan Pacific ADAPTOR, SMA MALE TO BNC FEMALE
$6.96 $6.29
Pan Pacific ADAPTOR, SMA MALE TO N MALE
$11.50 $10.39
Pan Pacific ADAPTOR, TNC FEMALE TO RFN MALE
$9.04 $8.19
Pan Pacific ADAPTOR, UHF FEMALE TO F MALE
$7.40 $6.69
Pan Pacific ADAPTOR, UHF MALE TO F FEMALE
$8.24 $7.39
RDL Adjustable Gain Microphone Preamplifier - 35 to 65 dB gain
Radio Design Labs STM-2, Adjustable Gain Microphone Preamplifier - 35 to 65 dB gain Features: Low-Noise Mic Preamp Adjustable Output Level High or Low Impedance Mic Inputs Mic Input to 2 Line Outputs Two Balanced or Unbalanced Outputs Phantom Capability RF-Filtered Inputs Input: 500 Ω balanced; 5 kΩ unbalanced Phantom: 24 Vdc; IEC 61938: 2013, Filtered Outputs (2): +4 dBu 150 Ω balanced; -10 dBv unbalanced Frequency Response: 50 Hz to 30 kHz (± 1.5 dB) Gain: Adjustable 35 to 65 dB THD+N: < 0.05% (50 dB Gain) CMRR: >50 dB (50 Hz to 20 kHz) Residual Noise: < -70 dB (below +4 dBu 150 Ω source @ 50 dB gain) Headroom: > 20 dB (24 Vdc supply); > 14 dB (12 Vdc supply) Phantom Power Input: 24 to 33 Vdc @ 10 mA maximum Power Requirement: GROUND-REFERENCED, 24 to 33 Vdc @ 25 mA Ambient Operating Environment: 0° C to 55° C Dimensions: Height: 0.7 in. (1.7 cm), Width: 3 in. (7.6 cm), Depth: 1.6 in. (3.9 cm) Package Type: Cardboard Box Package Dimensions: 2 x 2 x 4 in. Shipping Weight: 0.195 lbs. WEEE weight: 0.145 lbs. Tariff code: 8543.70.9960
$273.96 $205.47
Jonard Adjustable Round Hole Cutter
Jonard Tools, AHC-10, Adjustable Round Hole Cutter Cuts plywood, sheetrock, plasterboard, and acrylic sheet up to 1 1/16” (2.7 cm) thick Cutting depth is adjustable via hex locknut and compression spring Cuts hole sizes from 2.2” (55 mm) to 10” (254 mm) Polycarbonate transparent dust shield collects dust and prevents chips from flying into eyes while cutting Rubber gasket provides surface protection against damage, tight seal against flat surfaces, and prevents fallout from debris Compression spring absorbs vibrations while cutting Can be used with any variable-speed drill
$140.29 $115.95
Jonard Adjustable Round Hole Cutter w/ Vacuum Port, 9" - Jonard Tools AHC-19
Jonard Tools AHC-19 Adjustable Round Hole Cutter w/ Vacuum Port, 9" Designed for cutting round holes in ceilings, walls, and floors without making a mess, the AHC-19 is the perfect tool for installing recessed speakers, lighting, or other round objects. This adjustable hole cutter features the following: Can be hooked up to vacuums, with 2.5" (63.5 mm) diameter hose nozzles, to suck up debris as you go Cuts plywood, sheetrock, plasterboard, and acrylic sheet up to 1 1/16” (27 mm) thick Cutting depth is adjustable via hex locknut and compression spring Cuts hole sizes from 2.2" to 9" (56 mm - 228.6 mm) in diameter Polycarbonate transparent dust shield collects dust and prevents chips from flying into eyes while cutting Rubber gasket provides surface protection against damage, tight seal against flat surfaces, and prevents fallout from debris Compression spring absorbs vibrations while cutting Can be used with any variable-speed drill Power drill and vacuum not included with hole cutter Product Includes:1 Cover, 1 Adjustable Hole Cutter, 1 Vacuum Port, 1 Cap, 1 Nut, 1 Set of Replacement Blades, 1 Hex Key, and a Rugged Carry Case Cut Type Round Hole Works On Plywood, Sheetrock, Plasterboard, Acrylic Sheet Cutting Diameter Range 2.2"- 9" (56 mm-228.6 mm) Vacuum Port Size 2.5" (63.5 mm) Maximum Cutting Depth 1.1" (27 mm) Bit Diameter 0.236” (6.0 mm) Bit Length 2.17” (55 mm) Bit Material Steel Hex Chuck Size/Arbor Size 3/8" (9.53 mm) Dimensions 13" x 4.50" x 13" (33 cm x 33 cm x 11.4 cm) Product Material Steel Weight 6.28 lb (2851.12 g)
$155.19 $136.95
