Welcome to Tri-Tek Electronics

Surface Mount Mini IR Receiver - Dual Band

Description

PI Mfg TTA‑1178 Surface Mount Mini IR Receiver — Closeout Special


Overview

The PI Manufacturing TTA‑1178 Surface Mount Mini IR Receiver (Dual Band) is a compact, low-profile infrared sensor module designed to receive IR commands from remote controls over both standard and expanded IR bands. As a closeout item, it is offered in limited quantities, while stock lasts.

As an authorized distributor, Tri‑Tek Electronics provides full manufacturer warranty coverage and local support for installers, AV integrators, and system designers in the Phoenix / Mesa, AZ region.


Key Features

  • Dual‑band infrared reception (supports broad IR remote frequencies)

  • IR pickup range up to ~ 40 feet

  • Blue LED indicator to confirm IR reception

  • 3-meter integral cable (prewired)

  • 3.5 mm stereo mini‑plug connector

    • Tip = Signal

    • Ring = +V

    • Sleeve = Ground

  • Surface‑mountable housing, unobtrusive design

  • Compact footprint ideal for tight installations


Typical Use / Installation Example

This mini IR receiver is ideal for home theater, custom AV racks, or cabinetry where you wish to place an IR “eye” behind a small window (e.g. plastic or acrylic) or exposed discreetly. You mount the unit in a flush or surface-mount position and route the cable back to your IR control system or IR repeater block. The dual-band design ensures compatibility with a wider variety of remote control frequencies, minimizing “dead zone” issues.

For example, in a media cabinet with smoked glass doors, you might install the TTA‑1178 directly behind a small IR-transparent decal or window. The 3 m cable then carries the IR signal back to your IR processor or system controller.


Specifications

Parameter Specification
IR Frequency / Band Dual band (wide remote compatibility)
Range ~ 40 ft
Indicator Blue LED (IR reception confirmation)
Cable Length 3 meters
Connector 3.5 mm stereo mini‑plug
Pinout Tip = Signal, Ring = +V, Sleeve = Ground
Mounting Surface mount housing (low profile)
Warranty Full manufacturer warranty via Tri‑Tek Electronics
Special Note Closeout item — limited inventory

Important Notes & Recommendations

  • Because this is a closeout product, once current inventory is depleted, it will not be restocked.

  • Use care when routing the IR cable: avoid sharp bends and maintain good grounding to reduce noise or interference.

  • The LED confirmation helps with alignment and setup: place the receiver eye where the LED is visible during commissioning.

  • If mounting behind a cover or window, ensure the covering material is IR‑transparent (e.g. thin acrylic, IR-permeable plastic) to avoid signal attenuation.

  • In long cable runs, verify voltage at the receiver end and avoid excessive voltage drop.


Why Buy Through Tri‑Tek Electronics?

  • Authorized distributor status ensures full factory warranty, product authenticity, and support.

  • Local AZ presence in Mesa / Phoenix ensures faster delivery, easier returns, and local technical assistance.

  • Closeout pricing advantage—you benefit from reduced cost while quality remains factory-grade.

Would you like me to prepare a wiring diagram, high‑res render of the unit for your web page, or a printable installation guide?

Product form

PI Mfg TTA‑1178 Surface Mount Mini IR Receiver — Closeout Special Overview The PI Manufacturing TTA‑1178 Surface Mount Mini IR... Read more

Free local pickup in our store

SKU: PITTA-1178

2 in stock

$25.99 $23.81

    • Shipped today? Order within: Oct 01, 2025 14:00:00 -0700

    Description

    PI Mfg TTA‑1178 Surface Mount Mini IR Receiver — Closeout Special


    Overview

    The PI Manufacturing TTA‑1178 Surface Mount Mini IR Receiver (Dual Band) is a compact, low-profile infrared sensor module designed to receive IR commands from remote controls over both standard and expanded IR bands. As a closeout item, it is offered in limited quantities, while stock lasts.

    As an authorized distributor, Tri‑Tek Electronics provides full manufacturer warranty coverage and local support for installers, AV integrators, and system designers in the Phoenix / Mesa, AZ region.


    Key Features

    • Dual‑band infrared reception (supports broad IR remote frequencies)

    • IR pickup range up to ~ 40 feet

    • Blue LED indicator to confirm IR reception

    • 3-meter integral cable (prewired)

    • 3.5 mm stereo mini‑plug connector

      • Tip = Signal

      • Ring = +V

      • Sleeve = Ground

    • Surface‑mountable housing, unobtrusive design

    • Compact footprint ideal for tight installations


    Typical Use / Installation Example

    This mini IR receiver is ideal for home theater, custom AV racks, or cabinetry where you wish to place an IR “eye” behind a small window (e.g. plastic or acrylic) or exposed discreetly. You mount the unit in a flush or surface-mount position and route the cable back to your IR control system or IR repeater block. The dual-band design ensures compatibility with a wider variety of remote control frequencies, minimizing “dead zone” issues.

    For example, in a media cabinet with smoked glass doors, you might install the TTA‑1178 directly behind a small IR-transparent decal or window. The 3 m cable then carries the IR signal back to your IR processor or system controller.


    Specifications

    Parameter Specification
    IR Frequency / Band Dual band (wide remote compatibility)
    Range ~ 40 ft
    Indicator Blue LED (IR reception confirmation)
    Cable Length 3 meters
    Connector 3.5 mm stereo mini‑plug
    Pinout Tip = Signal, Ring = +V, Sleeve = Ground
    Mounting Surface mount housing (low profile)
    Warranty Full manufacturer warranty via Tri‑Tek Electronics
    Special Note Closeout item — limited inventory

    Important Notes & Recommendations

    • Because this is a closeout product, once current inventory is depleted, it will not be restocked.

    • Use care when routing the IR cable: avoid sharp bends and maintain good grounding to reduce noise or interference.

    • The LED confirmation helps with alignment and setup: place the receiver eye where the LED is visible during commissioning.

    • If mounting behind a cover or window, ensure the covering material is IR‑transparent (e.g. thin acrylic, IR-permeable plastic) to avoid signal attenuation.

    • In long cable runs, verify voltage at the receiver end and avoid excessive voltage drop.


    Why Buy Through Tri‑Tek Electronics?

    • Authorized distributor status ensures full factory warranty, product authenticity, and support.

    • Local AZ presence in Mesa / Phoenix ensures faster delivery, easier returns, and local technical assistance.

    • Closeout pricing advantage—you benefit from reduced cost while quality remains factory-grade.

    Would you like me to prepare a wiring diagram, high‑res render of the unit for your web page, or a printable installation guide?

    Recently viewed products

    © 2025 Tri-Tek Electronics, Powered by Shopify

      • American Express
      • Apple Pay
      • Diners Club
      • Discover
      • Google Pay
      • Mastercard
      • PayPal
      • Shop Pay
      • Visa

      Login

      Forgot your password?

      Don't have an account yet?
      Create account